 |
 VINTAGE ROL EZE KNIFE SHARPNER USED GOOD CONDITION ITS THE 1 1 2 N DIAMETER 1 $13.00 Time Remaining: 14d 12h 51m Buy It Now for only: $13.00 |
Diameter Knife
Crispy Coconut Cookies
For the coconut lover, this recipe will without doubt, be well suited to them. Very crispy under the teeth, this cookie is perfect to be consumed at tea-time or to accompany any coffee break or afternoon tea.
For this recipe we will need a stencil about 5cm diameter and 2mm thick to spread and shape the cookies on the baking silicon sheet. The stencils are usually made of aluminium or rubber and we can find them in bakery utensils specialty shops. By using a stencil we are able to make regularly sized and shaped cookies.
First thing we need, as usual, to turn on the oven but this time at the very low temperature of 80ºC to 90ºC (176ºF to 194ºF) depending of the oven.
Following are the ingredients needed for this recipe:
Egg Whites: 125g
Castor sugar (1): 70g
Castor sugar (2): 375g
Plain water: 100g
Desiccated coconut: 450g
Vanilla essence: 4g
Another particularity of the recipe is that it cannot be made for a last minute plan, the baking time being 12 hours.
First we need to start cooking the castor sugar (2) with the plain water, and we are going to cook it to the soft ball, this means to 113ºC (235ºF) if we use a thermometer.
When the sugar reach 106ºC (223ºF) we can start whisking the egg whites with the castor sugar (1) preferably with an electric mixer on 3rd gear.
When the hot syrup reach 113ºC (235ºF) the egg whites should have already formed a soft snow. Then we pour very slowly the hot syrup into the egg white, whisking constantly on second gear, this time.
Then after scrapping the side of the bowl with a long handle mounted scrapper or spatula, turn the mixer up to the 3rd gear again for a few second (to clean the whisk) and then back to second gear; and leave it for a few more minutes on 2nd gear to cool down slightly.
When the meringue is still warm and not too hot anymore, take the bowl off the mixer and fold in the desiccated coconut and vanilla essence, mixing by hand with spatula or big spoon.
At this stage we get a very sticky white paste. So we can start shaping the cookies with the help of the stencil and a small palette knife on a non-stick silicon baking sheets, keeping the disks 1cm apart each others.
Once you have finished shaping the whole mix take off the stencil(s) and insert the baking sheets into the oven.
If your oven has a ventilation duct, keep it open. If your oven does not have a ventilation duck, then it is better to leave a very small opening on the side of the door, as we need the cookies to dry out completely.
The coconut disks should stay as white as at the beginning, during the whole length of the baking up until the end. If they start to take a yellowish colour during the baking, this means that the oven is too hot.
After 12 hours of baking the coconut disks should be very crispy, brittle and still virgin white.
Take them out and leave them to cool down completely.
When they are cold, it is a good idea to place them in an airtight container, this way they will stay dry and crispy.
I really hope you enjoyed this coconut disk cookies recipe.
For more interesting recipes please visit my Blog Here.
This article was originally published in "How to Prepare Some Crispy Coconut Disks".
About the Author
Jac Paillard is a pastry chef and has been in this trade for quite a few years already. During those years he has been working in few countries: first France (Dreux, Paris, Lyon), Switzerland (Zurich) and Germany (Frankfurt). Then moved to Australia where he worked for a few years before getting a position in Indonesia in a well known hotel chain. Then after a few years again he moved back to Australia where he is living at the present time.
In this articles he is sharing with the readers some of the knowledge, tips and recipes that he has been accumulating over the years. Jac really hopes you will enjoy the reading and would very much like to hear from you again soon.
Does anyone know where I can find an old ceramic fuse that is about 7 in long and 4 in diameter?
My dad had an old ceramic fuse that was about 7in x 4in with a metal plate attached to one end with screw holes. Someone gave it to him to use as a knife sharpener. He recently lost it and I want to replace it for him.
Have any friends at the power company? Electricians that have access to those beauties sometimes have a supply. Mine is a ceramic rod that came out of a streetlamp.
Knife Review: Byrd Flight (Cheap and Slippery (Not in a good way))